Edge-lighting Cirrus Float for Monorail Bedienungsanleitung PDF herunterladen

Installation Instructions for Cirrus Float D1 For Fast Jack, Monorail,

and Monorail Two Circuit

Install the Fast Jack Connector to Coaxial Power Cable

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

SAVE THESE INSTRUCTIONS!

- This product is suitable for indoor dry locations.

- This instruction shows typical installation for Fast Jack

canopies, Monorail, and Monorail Two Circuit.

- For installation on T-Bar Clip use the Cirrus T-Bar clip

instructions (904-CS-TBAR) concurrently with these

instructions.

IMPORTANT INFORMATION

904-FJ-CF-D1-01

FJ-CF-D1-_

M-CF-D1-_

1: Loosen the M4 set screw on base of the coaxial fixture

connector with the 2mm Allen wrench provided. Do not

remove this set screw.

2: Remove the M3 set screw on tip of the connector with the

1.5mm Allen wrench provided.

COAXIAL CABLE

INSULATION

WIRE STRIPPER

3: Use the #12 gauge hole of the AWG wire strippers to strip

1" of the insulation cover from the end so that the bare

coaxial cable is exposed.

CONICAL NIPPLE

STRAIN RELIEF TUBE

OUTER METAL JACKET

INSULATION

4: Feed the coaxial cable through the conical nipple and flared

side of the strain relief tube. Slide the conical nipple down

the coaxial cable. Slide the strain relief tube against the

insulation.

5: Use the #14 gauge hole of the AWG wire strippers to strip

the outer metal jacket exposed behind the strain relief tube.

1.5MM ALLEN

WRENCH

2MM ALLEN

WRENCH

M4 SET SCREW

M3 SET

SCREW

COAXIAL FIXTURE CONNECTOR

M2-CF-D1-_

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - IMPORTANT INFORMATION

Installation Instructions for Cirrus Float D1 For Fast Jack, Monorail, and Monorail Two CircuitInstall the Fast Jac

Seite 2 - Canopy (FJP-26RE-XX)

6: Feed the inner coaxial cable along with strain relief tube into the coaxial fixture connector. D6STRAIN RELIEF TUBEINNER WIREFIXTURE CONNECTOR9

Seite 3

2: Screw the conical post provided with the fixture hardware completely on to one of the Fast Jack ports.3: Insert the adjustable connector comple

Seite 4

Install Cirrus Float to Single or Multi Port Fast Jack Canopies 9: Push the tab on the adjustable connector and feed the aircraft cable through th

Seite 5 - M3 SET SCREW

9: Push the tab on the adjustable connector and feed the aircraft cable through the tab.10: Pull the aircraft cable coming out of the side of th

Seite 6 - CIRCUIT #1 CIRCUIT #2

Install Cirrus Float to Monorail 2 CircuitNOTE: To install the aircraft cable side of the fixture onto the ceiling, follow steps 3 through 11 and 13 i

Kommentare zu diesen Handbüchern

Keine Kommentare

Edge-lighting Cirrus Float for Monorail Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Edge-lighting Cirrus Float for Monorail herunter. Edge Lighting Cirrus Float for Monorail User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Edge-lighting Cirrus Float for Monorail